top of page

Installation Instructions

Need more help? Contact us. 

These installation instructions are a guideline.  Uzarski Designs assumes no responsibility for improper disassembly/reassembly of your equipment.

1. Empty the marker and gather components

Tip: Don't install the rubber grip over core until core is installed on marker. It's difficult to remove when not installed.

  • Look into feedneck and verify there are no paintballs in the marker.

  • De-gas marker by turning the cam drive knob counter-clockwise.

  • Remove the air tank.

  • Gather the lightweight foregrip.

  • Gather a Field One LiPo battery (sold separately).

Empty marker and gather components_edite
2. Remove Battery Door and AA Batteries

Tip: The battery door release screw only needs to be rotated ~¼ turn before the battery door pops out. Rotate the screw in the direction indicated on the battery door.

  • Determine the orientation of battery door’s release screw arrow.

Battery Door_edited.jpg

  • Use a 1/8” hex key to rotate the battery door’s release screw ~¼ turn. The door should pop out.

Screenshot 2023-08-01 at 3.23.06 PM.png

  • Remove the battery door.

  • Remove AA batteries. 

Screenshot 2023-08-01 at 3.24.45 PM.png
3. Disconnect the Foregrip and Reversal Plate

Tip: When the foregrip core screws are removed, the grip will be connected to the frame via the battery harness. Use care not to put tension on the harness.

  • Hold the foregrip in place and use a 1/8” hex key to fully loosen the screws within each of the two springs inside the foregrip.  The screws will stay retained within foregrip.

Screenshot 2023-08-01 at 3.26.55 PM.png

  • Carefully separate the foregrip so there is no tension on the battery harness.

Screenshot 2023-08-01 at 3.28.17 PM.png

  • Place the marker on a flat surface so the foregrip does not put tension on the battery harness.

  • Use a 1/8” hex key to remove the two screws retaining the reversal plate.

Remove Screws Reversal Plate Screws_edit

  • Carefully separate the reversal plate from the body so there is no tension on the battery harness.

Separate Reversal Plate.png
4. Disconnect the Battery Harness

  • Detach the battery harness from the bridge board by carefully pulling it out.

  • Set the foregrip, reversal plate, and battery harness to the side.

Untitled video - Made with Clipchamp.gif
5. Install the Lightweight Foregrip

  • Align the core to the body where the reversal plate was installed.

IMG_7521_edited.jpg

  • Install the forward screw and tighten it with a 5/32” hex key.

IMG_7525_edited.jpg

  • Install the rear screw and tighten it with a 1/8” hex key. 

IMG_7526.JPG

  • Slide the rubber over-grip over the core until the upper tabs are about to engage.

IMG_7528_edited.jpg

  • Tuck the side tabs into the core and install the rubber over-grip the rest of the way.

  • Press the rear tab into the core until the rear of the grip sits against the marker.

IMG_7536_edited.jpg

  • Press firmly all around the grip to ensure all the internal engagement features are seated

6. Install the LiPo Rechargeable Battery

  • Orient the marker so the barrel is to the right.

  • ​Use a 5/64” hex key to remove the three grip frame screws.

IMG_7537_edited.jpg

  • Open the grip panel.

  • ​Toggle the power selector switch to “LiPo”.

IMG_7540_edited.jpg

  • Connect the LiPo battery to the board’s connector labeled “LiPo”.

IMG_7541 (1)_edited_edited.jpg

  • Close the grip panel.

  • Install and tighten the three grip frame screws with a 5/64” hex key.

bottom of page